#!/bin/bash
# Load the standard experimental sequence

./dcset -p /dev/ttyUSB0 -o c # Clear the experiment

./dcset -p /dev/ttyUSB0 -o e -t 0 # Add an event at time 0
# Load trap

./dcset -p /dev/ttyUSB0 -o a -n 2 -v 145 # Repump laser on
./dcset -p /dev/ttyUSB0 -o a -n 1 -v 145 # Cooling laser on
./dcset -p /dev/ttyUSB0 -o a -n 8 -v 241 # Cooling laser detuning default
./dcset -p /dev/ttyUSB0 -o d -n 3 -v 1 # MOT coil on
./dcset -p /dev/ttyUSB0 -o d -n 1 -v 0 # Camera trigger low
./dcset -p /dev/ttyUSB0 -o d -n 2 -v 0 # Getter current off
./dcset -p /dev/ttyUSB0 -o f  # Finish this event

#./dcset -p /dev/ttyUSB0 -o e -t 625 # After 10 ms (=625 timer cycles) turn off Bfield, reduce cooling 
				    # intensity and repump intensity to do sub doppler cooling
#./dcset -p /dev/ttyUSB0 -o a -n 1 -v 50 # Cooling laser low
#./dcset -p /dev/ttyUSB0 -o a -n 2 -v 25 # Repump laser low
#./dcset -p /dev/ttyUSB0 -o a -n 8 -v 50 # Increase Cooling laser detuning default
#./dcset -p /dev/ttyUSB0 -o d -n 3 -v 0 # MOT coil off
#./dcset -p /dev/ttyUSB0 -o f  # Finish this event

./dcset -p /dev/ttyUSB0 -o e -t 937 # Switch off cooling, repump
# Take a picture
./dcset -p /dev/ttyUSB0 -o a -n 1 -v 0 # Cooling laser off
./dcset -p /dev/ttyUSB0 -o a -n 2 -v 0 # Repump laser off
./dcset -p /dev/ttyUSB0 -o d -n 3 -v 0 # MOT coil off
#./dcset -p /dev/ttyUSB0 -o d -n 1 -v 1 # Trigger camera
./dcset -p /dev/ttyUSB0 -o f  # Finish this event

#./dcset -p /dev/ttyUSB0 -o e -t 940 # Trigger kicks
## Trigger kick laser pulses
#./dcset -p /dev/ttyUSB0 -o d -n 4 -v 1 # Pulse gen trigger
#./dcset -p /dev/ttyUSB0 -o f  # Finish this event

#./dcset -p /dev/ttyUSB0 -o e -t 960 # Turn off kick trigger
## Trigger kick laser pulses
#./dcset -p /dev/ttyUSB0 -o d -n 4 -v 0 # Pulse gen trigger
#./dcset -p /dev/ttyUSB0 -o f  # Finish this event

# Wait 15 ms and then get a shot 

#./dcset -p /dev/ttyUSB0 -o e -t 1898 # Add an event at time 250
./dcset -p /dev/ttyUSB0 -o e -t 950 # Add an event at time 250
# Reset Trigger
./dcset -p /dev/ttyUSB0 -o a -n 2 -v 145 # Cooling laser on
./dcset -p /dev/ttyUSB0 -o a -n 1 -v 145 # Repump laser on
./dcset -p /dev/ttyUSB0 -o a -n 8 -v 241 # Cooling laser detuning default
./dcset -p /dev/ttyUSB0 -o d -n 1 -v 1 # Trigger camera
./dcset -p /dev/ttyUSB0 -o f  # Finish this event

# Turn the MOT coil back on, camera trigger off
./dcset -p /dev/ttyUSB0 -o e -t 13480 # Add an event at time 255
# Turn the trap back on 
./dcset -p /dev/ttyUSB0 -o d -n 1 -v 0 # Trigger camera
./dcset -p /dev/ttyUSB0 -o d -n 3 -v 1 # MOT coil on
./dcset -p /dev/ttyUSB0 -o f  # Finish this event

# Now print the experiment to the serial port
./dcset -p /dev/ttyUSB0 -o p # print to serial